Midco RE32 Manuel d'utilisateur télécharger pdf

MIDCO International Inc.

4140 WEST VICTORIA STREET, CHICAGO, ILLINOIS 60646 / (773) 604-8700 FAX: (773) 604-4070 / http://www.midco-intl.com

The ECONOMITE Model RE32 intermittent spark ignition conversion burner is adaptable to most gas utilization equipment,

including gravity and forced circulation furnaces and boilers, and is particularly recommended for horizontal and downdraft gas

utilization equipment since it needs no draft to maintain a pilot. Power burner design makes it perfectly suited for oil burner

replacement.

Do not store or use gasoline or other

flammable vapors and liquids in the

vicinity of this or any other appliance.

WHAT TO DO IF YOU SMELL GAS

● Do not try to light any appliance

● Do not touch any electrical switch;

do not use any phone in your building.

● Immediately call your gas supplier

from a neighborÕs phone. Follow the

gas supplierÕs instructions.

● If you cannot reach your gas

supplier, call the fire department.

Installation and service must be

performed by a qualified installer,

service agency or the gas supplier.

INSTALLATION AND

SERVICE INSTRUCTIONS

ECONOMITE MODEL RE32

Gas Conversion Burner

PRINTED IN U.S.A.

197

8470-01

WARNING: If the information in

these instructions is not followed

exactly, a fire or explosion may

result, causing property damage,

personal injury, or death.

In the United States, installation must conform with local codes or,

in the absence of local codes, with Installation of Domestic Gas

Conversion Burners, ANSI Z21b-latest edition, and National

Fuel Gas Code, ANSI Z223.1-latest edition, available from

American National Standard Institute. Further reference should

be made to the recommendation of your fuel supplier.

NOTE: Any additions, changes, or conversions required in order for

the gas utilization equipment to satisfactorily meet the application

needs must be made by a MIDCO distributor (or other qualified

agency) using factory specified and approved parts.

In Canada, installation must conform with local codes or, in the

absence of local codes, with Installation Codes for Gas Burning

Appliances and Equipment, CGA Standard CAN/CGA 1-B149.1

or 2. When the conversion burner is used on Forced Air Central

Furnace, the two yellow and black warning labels in the literature

envelope shall be attached in accordance with Installation Code,

CGA Standard CAN/CGA 1-B149, Clause 5.4.4.4. Further

reference should be made to the recommendation of your

fuel supplier.

INSTALLER: Inform and demonstrate to the

user the correct operation and maintenance of

this gas utilization equipment. Inform the user

of the hazards of storing flammable liquids

and vapors in the vicinity of this gas utilization

equipment and remove such hazards. Affix

this manual adjacent to the conversion burner.

CODE COMPLIANCE IS THE SOLE

RESPONSIBILITY OF THE INSTALLER.

USER: Retain this manual for future reference.

If other than routine service or maintenance

as described in this manual is required,

contact a qualified service agency. DO NOT

ATTEMPT REPAIRS. An inadvertent service

error could result in a dangerous condition.

SAFETY INFORMATION TERMS: The following terms are used to identify hazards, safety precautions or special notations and have

standard meanings throughout this manual. When you see the safety alert symbol and one of the safety information terms, as

shown below, be aware of the hazard potential.

DANGER: Identifies the most serious hazards which will result in severe personal injury or death.

WARNING: Signifies a hazard that could result in personal injury or death.

CAUTION: Identifies unsafe practices which would result in minor personal injury or product and property damage.

ANSI Z21.17

CONVERSION

BURNERS

1 2 3 4 5 6 7 8

Résumé du contenu

Page 1 - MIDCO International Inc

MIDCO International Inc.4140 WEST VICTORIA STREET, CHICAGO, ILLINOIS 60646 / (773) 604-8700 FAX: (773) 604-4070 / http://www.midco-intl.comThe ECON

Page 2 - PART 1 INSTALLATION

around door frames, to prevent leakage into or out of thecombustion chamber. The access or firing door should open easily to relievepressure. If po

Page 3 - DRAFT CONTROL

WARNING: BURNER CABINET MUST BE MOUNTEDIN ORIENTATION SHOWN IN FIGURES 2 AND 3.ANY OTHER MOUNTINGS MAY CAUSE DANGEROUSC

Page 4 - VI PIPING

-4-V ELECTRICALInstallation wiring and grounding of the burner must conform tolocal codes, or, in their absence in the United States toNational Electr

Page 5 - VII MAIN GAS SPUD

VII MAIN GAS SPUDStandard burners are approved for use with NATURAL orPROPANE gas and should be used only with the gas specifiedon the rating plate.

Page 6 - PART 2 SERVICE

PART 2 SERVICEDANGER: Be sure the manual Main Shut-Off Valve combination valve and Burner Power Switch are turned OFF before removing any parts for s

Page 7 - XII ELECTRONIC CONTROL SYSTEM

manifold gas pressure of 2.0" W.C. If pressure adjustment isrequired for setting capacity, remove regulator cap for accessto slotted adjustment s

Page 8 - TROUBLE CHART

-8-TROUBLE CHARTMake sure the thermostat and operating controls are calling for heat. Defective wiring or loose connections can simulate thecomponent

Commentaires sur ces manuels

Pas de commentaire

Midco RE32 Manuel d'utilisateur

Naviguer en ligne ou télécharger Manuel d'utilisateur pour Équipement Midco RE32. Midco RE32 User Manual Manuel d'utilisatio

Résumé du contenu

Commentaires sur ces manuels

Produits connexes et manuels pour Équipement Midco RE32